Pcsa-sp1 sip software

Each time you press this button, the location of the window picture changes. When initializing is complete, blinks in green.

Message Incorrect dialing setup. Unknown network error: Number does not exist: 2,3,6 Network congestion: Normal disconnection: Line is busy: 18,19 System not responding Page Message Dialing your own number is invalid. GateKeeper error. Busy line - Connection not possible. Far end inactive System not responding. Close this menu to connect line Cannot establish all connections Connection time out.

Communication error Configuration error MCU operation rejected. Corrupted data stream-Terminating connection. Page Message No Memory Stick. Memory Stick write-protected. Memory full. Memory Stick file error. Memory Stick file decode error. Memory Stick size error. There are no images recorded in the Memory Stick. File error. File size error. File decode error. Format error. Settings cannot be changed during communication. Page You cannot use the Data Solution Box. The battery in the stylus for the whiteboard is low.

Replace the battery in the stylus with a new one. Page Message Some trouble occurs during connection. Connection has failed. Check the information registered to the gatekeeper.

Connection has been rejected as the data exceeds the bandwidth of a gatekeeper. Gatekeeper does not respond. The ISDN line is invalid. Check the ISDN connection. LAN configuration error. PPPoE server admission fails. Dial again after confirmation of the PPPoE settings. Page Message LAN configuration error. Connection is not complete as an invalid port number is specified. Line is busy. Try to dial again later. Set it correctly.

Line connected with 1B 64K. Local number setting for ISDN configuration may not be correct in the remote party. Initialization error. Connection using SIP is not available. Unauthorized handle. Maximum sessions over. Server internal error.

Provisional response timeout. Page The following messages indicate the state of the system. No action is required. Message Meeting starts!

Starting connection. Meeting ends. Please wait. Installation completed. The still image has been sent. Still image transmission cancelled. Preset 1 —6 selected. Still image saved to Memory Stick. You cannot use the Private Phone Book. Page Troubleshooting Replace the batteries with new ones page Turn off the system immediately and consult with Sony dealer. Adjust the volume of the TV monitor. Page Symptom Cause No picture.

The selected picture source is not tuned on. Video input is not selected properly. Select the video input with the The selected picture source is not correctly connected to the System. A voice meeting is held. Movement of the camera is prevented. Page Symptom Cause No connection. Some of the system settings are not correct. Answering the call is not permitted by the remote terminal as it is operating for setups, etc. The remote terminal is not set to auto answer mode.

The ISDN telephone numbers are not set up in the remote terminal when using bonding. Specifications Signal Port number Page Videoconferencing Room Layout Videoconferencing Room Layout Be sure to position camera and microphone appropriately in your videoconferencing room.

Camera Range represents the shooting area of the camera when the zoom has been extended fully. Avoid direct light on the TV monitor. Light intensity on faces should be about lux or more. If an inverter type or brightness-adjustable type of fluorescent lamp is used, the sensitivity of the Remote Commander may deteriorate.

Dialing the first ISDN line only enables you to connect all other lines. Dialing the second and later lines is automatically done by the communication between the videoconferencing systems on both sites. Page G. A phone bandwidth audio signal is converted to a digital signal with a data rate of 16 Kbps.

Gatekeeper Controls the access of H. Page Lip synchronization A function that synchronizes sound with motion. To sign out a device from the Admin center, follow these steps:. The pairing code is time-sensitive. If it expires, the user must press Back on the phone and start the sign-in process again. Navigate to the authentication URL on the user's desktop or mobile browser and use corporate credentials to log in.

Enter the pairing code displayed on the SIP phone into the web authentication app to pair the SIP phone with the user's account. On a successful sign-in, which might take a while, the SIP phone will display the phone number and username, if the device supports it. The location of the device shown on the Azure Active Directory web authentication app is the SIP Gateway datacenter to which the device is connected. Learn more here: Microsoft identity platform and the OAuth 2.

On the device's Details pane , select the Details tab, and at the upper right on the Actions menu, select Sign out. You can view and monitor your SIP device inventory in the Teams admin center after the devices' users sign in at least once. All signed-in SIP devices are listed on the right.

On the right, select the SIP device that you want to restart, and then select Restart. User details and policies will be fetched to SIP devices when users sign in.

Any policy changes thereafter for signed-in users will be synced to the device within one hour. Devices must have their registration refreshed with the SIP Gateway periodically. A SIP device can usually display information in many languages. SIP Gateway only supports static—also called registered—emergency addresses. Currently, registered addresses are not supported for Direct Routing scenarios. For more information about emergency calling, see Plan and manage emergency calling.

To report problems, contact Microsoft Support. Skip to main content. This browser is no longer supported. Download Microsoft Edge More info. Contents Exit focus mode. Please rate your experience Yes No.

Worksheet 4 wont be effective until next quarter. This has been fixed. The problem has been fixed. Household Limit has been changed from to the new limit. This checkbox defaults to being checked every time you enter this screen. Made some changes when creating Electronic Locality W2 file. This especially concerns Kansas City. You will need to recreate the electronic file after installing this update. The Modify now includes a NEC option. CA SDI rate has been updated. The correct screen now shows.

Note: the print option was correct.